6.02 ( Sep 30, 2020 ) --------------------- ( Note this doesn't change anything for the user. No need to update ) - Fixed bug with tester (right output transformer switching) - Add audio path debug tones to tester. 6.01 ( Sep 9, 2020 ) ----------------------- - Fixed bugs with tester (white led, midi tests) - Fixed firmware display at startup. 6.00 ( September 23, 2019 ) ---------------------------- - Added Freezification mode (ambient red). The select stomp provides the freezification of the the sound, thing 1 sets the transition speed, thing 2 sets the frozen sound level. - Added Skitter mode (delay + reverb yellow). Thing 1 sets the diffusion, thing 2 sets the size. This sounds like delays that morphs into reverb. - Added SEED mode (ambient yellow). Sweet sound of a growing tail with lots of modulation, and width that opens wide while it decays. Happened upon this this while working on Skitter mode. Thing 1 is diffusion, thing 2 is size. 5.05 ( May 28, 2019 ) --------------------- - Updated automatic version detection system used for internal inventory tracking system. 5.04 ( February 23, 2019 ) ------------------------------------ - fixed spillover bug which occurred when you engaged the pedal from bypass in bank preset mode. - fixed: midi controller change messages were having their controller number zeroed before being passed through. 5.03 ( June 4, 2018 ) ------------------------------------ - V30 looper - lowered the sync timer so that stompswitch response has less latency. - changed combination stomp presses to happen on stompswitch press rather then release. - fixed choppiness in modulation modes. - fixed no octave sound in ambient green. 5.02 (not released yet) ----------------------- - V30 looper - hold the left and middle stompswitches for one second to clear the track - fixed a bug when trying to stop playback while looping. - added ability to tap left and middle stomp to navigate to previous track. - fixed bug that would occur if you recorded a very specific loop length of around 260 buffers. - volume knob now controls looper playback volume, when it's adjusted it in looper mode. - fixed tap tempo in delay+rev and reverse modes. - fixed MIDI issue with program changes causing preset 0 to be loaded (Thanks Brendan) - fixed amb blue not starting up with a delay sound (Thanks Daniel Eid). - made Ghost mode infinite hold a bit more controlled (volume doesn't swell as much). 5.01 (beta date: May 5, 2018) ----------------------------- -fixed MIDI 5.00 (beta date: May 4, 2018) ----------------------------------- - V30 looper - looper will corrupt whatever file system you have on the SD card, so don't use an SD card with important data on it! - works when effect is bypassed. - overdubbing implemented - always begin playing from start of loop - looper now requires a V30 SDHC card - fixed error with looper recording no sound after 20 seconds - presets can now be saved and loads from SD card - to save presets, make a directory in the root directory of the sd card called "from_reverb". On startup, Reverb will populate this directory with presets and the advanced config settings. - to load presets, make a directory in the root directory of the sd card called "to_reverb". Presets that are named NN_reverb.bin when NN is a number between 0 and 35 inclusive will be loaded into Reverb memory. - made shop tester easier to use 4.01 (beta date: Released on forum Sep 20, 2017) ------------------------------------------------ - first version of super beta multitrack looper. - merged with ES code. - tweaked the hacky preset spillover w/user suggestions. - added midi out of the knob and mode parameters to use with DAWs/Editors - added Advanced Config option for dryer mix taper under Hall Green. 1. wetter mix taper (default) 2. dryer mix taper (new) - fixed issue with trails someitmes not shutting off w/insert loop. 4.00 (beta date: May 30, 2017) ----------------------------- - added hacky preset spillover. (thanks Ian Jarrold and Rob Leishman) - added insert loop. (thanks Josh Cowell) - in advanced configuration, signal configuration now has four options. The last two are "Insert Pre Effect" and "Insert Post Effect" - right out/in acts as insert. - making infinite hold more infinite and less "infinite". (thanks Ian Jarrold) 3.04 (production date: February 24, 2017) ----------------------------------------- - fixed bug with shop tester that was failing good pedals. 3.03 (production date: December 12, 2016) ----------------------------------------- - "total lockdown" mode added to "knob lock" in advanced config. It's the 3rd option. It disables saving of presets. - fixed: dry signal was being momentarily cut when going from a full wet preset to bypass to full dry preset - shop tester was occasionally mis-writing factory settings 3.02 (production date: November 7, 2016) ---------------------------------------- - made shop tester easier to use 3.01 (production date: September 27, 2016) ------------------------------------------ - fixed bug with shop tester 3.00 (beta date: September 15, 2016) ------------------------------------ - added Glummer mode (Green Sparkle). Octave down and up. (thanks to Jim Quarnstrom) Thing controls are "octave down blend" and "octave up amount". - added Casper mode (Green Ghost). A friendlier less spooky ghost. (thanks to Landon Bailey) Thing controls are "modulation" and "diffusion". - added Destroyer Pad mode (Red Beer). For sternly communicating with misbehaving household appliances. (thanks to Josh Cowell) Things controls are "robot screams" and "pitch shift". 2.06 (beta date: August 25, 2016) --------------------------------- - fixed issue with advanced config option "Startup Engaged and load Preset 1" not working properly. (thanks to Brian Black) 2.05 (beta date: August 23, 2016) --------------------------------- - fixed issue with red reverse. max tap tempo time was longer than max RAM available, which would cause very loud scary sounds. (thanks to Paul Uhl) 2.04 (beta date: July 26, 2016) ------------------------------- - fixed issue with mix taper when using digital dry (like in lo-fi mode or when cab sim is engaged) - fixed issue with big thing2 changes causing clicks in audio. Unfortunately the clicks are unavoidable in some modes with both thing1 and thing2 changes. - fixed issue with heavy midi input causing pedal to freeze. (thanks Josh Cowell) - started adding stuff for the upcoming looper. 2.03 (beta date: July 6, 2016) ------------------------------ - fixed expression pedal bug where assigning expression pedal to too many parameters was freezing pedal (thanks to Takeo Yamamoto) - chose mix taper from 2.01 due to popular vote. 2.01 and 2.02 (beta date: June 19, 2016) ---------------------------------------- - added Tremverb mode. It's the forth submode (yellow) of the modulation mode. (thanks to Frank Biewer) - can now change presets using a MIDI CC#11 message (thanks to Rob Leishman) - modified mix knob taper. 2.01 and 2.02 have slightly different tapers. going to hold a poll in the Voting Forum to pick the winner (thanks to Travis Salisbury) 1.00 (production date: May 24, 2016) ------------------------------------ - initial release